foratvise
Get Started
not classifiable

Unspecified filler loss (unclassified cause)

not classifiableFilling

In short

It appears in about 1 of every 100 lines studied.

When it appears, it takes on average about 59 % of the line's lost time. Reported by 5 of the 120 studies that could observe it (good evidence).

What happens

The source reports aggregate time losses on the filler under generic headings such as equipment, operational or planned losses, without identifying a specific failure mode, adjustment, stoppage reason or defect mechanism. The underlying physical or organisational cause of the lost time cannot be determined from the label alone, so it may correspond to any combination of breakdowns, minor stops, changeovers or scheduled downtime on the filling station.

What is done about it

Improve downtime data collection by requiring operators or the control system to tag every stop on the filler with a specific reason code (mechanical fault, format change, cleaning, lack of material, etc.) instead of a generic category, and audit the fault-coding structure in the MES. This enables reclassification of historical generic entries into actionable categories such as equipment failure, setup or organizational causes.

Practical guidance written from engineering knowledge; it is not a statistical estimate.

1Probability and evidence

Pooled over all segments. A wide interval is a result: it states how much the evidence allows us to know.
Probability of presence
1.4% [0.4–3.3%]
Expected share of lost time
0.8% [0.2–2.0%]
Share of lost time when present
59% [49–69%]
Studies / units
120 / 162
Evidence grade
B

Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.

2Probability by segment

Partially pooled estimates for each industry segment.
  • Dairy products
    2.0% [0.3–6.0%]18 studies
  • Soft drinks, bottled water and juices
    2.3% [0.6–5.5%]44 studies
  • Brewing, wine and spirits
    1.4% [0.2–4.5%]16 studies
  • Bakery and pasta
    1.8% [0.3–6.1%]0 studies
  • Meat, poultry and seafood
    1.6% [0.2–4.9%]6 studies
  • Fruit and vegetable processing
    1.7% [0.2–5.3%]4 studies
  • Grain and oilseed milling
    2.3% [0.4–7.5%]6 studies
  • Sugar and confectionery
    1.7% [0.2–5.4%]3 studies
  • Snacks, coffee, tea and other foods
    1.6% [0.2–4.9%]6 studies
  • Animal feed and pet food
    1.6% [0.2–5.2%]4 studies
  • Food manufacturing (unspecified or mixed)
    1.5% [0.2–4.7%]13 studies

3Mechanism, SCADA signature and countermeasure

Engineering guidance that helps recognise and address the cause; it is not part of the statistical estimate.

Mechanism

Engineering guidance

The source reports aggregate time losses on the filler under generic headings such as equipment, operational or planned losses, without identifying a specific failure mode, adjustment, stoppage reason or defect mechanism. The underlying physical or organisational cause of the lost time cannot be determined from the label alone, so it may correspond to any combination of breakdowns, minor stops, changeovers or scheduled downtime on the filling station.

How it looks in SCADA data

Engineering guidance

In SCADA/MES data this appears as time booked against broad loss buckets (equipment, operational, planned) for the filler without a linked fault code, alarm, or state transition detail, making it impossible to tie the duration to a specific machine state or sensor event. Analysts typically see only aggregated downtime totals per shift or per category rather than discrete event records.

Countermeasure

Engineering guidance

Improve downtime data collection by requiring operators or the control system to tag every stop on the filler with a specific reason code (mechanical fault, format change, cleaning, lack of material, etc.) instead of a generic category, and audit the fault-coding structure in the MES. This enables reclassification of historical generic entries into actionable categories such as equipment failure, setup or organizational causes.

4Sources

Every extracted datum with its study, value and verbatim quote.
  1. Lost time: 252,000 litre · as reported: “ilk üç sebep”
    Show verbatim quote
    Yukarıdaki Pareto grafiğinin incelenmesi sonucunda, ortaya çıkan ve aşağıda değerlendirmesi yapılan ilk üç sebebin 252.000 litre şurup kaybına neden olarak ortaya çıkan toplam şurup kaybının %88.4 lük kısmını oluşturduğu belirlenmiştir.
  2. Share of lost time: 88.4 % · as reported: “ilk üç sebep”
    Show verbatim quote
    ...ortaya çıkan toplam şurup kaybının %88.4 lük kısmını oluşturduğu belirlenmiştir.
  3. Share of loss events: 28.3 % · as reported: “Downtime Losses”
    Show verbatim quote
    Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
  4. Share of planned time: 2.27 % · as reported: “Downtime Losses”
    Show verbatim quote
    Reduce Speed Losses with an average proportion of 3.82% and a relative frequency of 39.01%, Downtime Losses with an average of 2.27% and a relative frequency of 28.31%, Defect Losses with an average of 1.58% and a relative frequency of 15.59%, Idle and Minor Stoppage with an average of 1.55% and a relative frequency of 15.85%.
  5. Share of lost time: 12.8 % · as reported: “machine downtime”
    Show verbatim quote
    machine downtime was reduced from 12.80% to 4.44%
  6. Share of lost time: 4.44 % · as reported: “machine downtime”
    Show verbatim quote
    machine downtime was reduced from 12.80% to 4.44%
  7. Share of loss events: 4.00 % · as reported: “No Code”
    Show verbatim quote
    No Code 192 4
  8. Number of events: 192 units · as reported: “No Code”
    Show verbatim quote
    No Code 192 4
  9. Lost time: 29.5 h · as reported: “Total Downtime”
    Show verbatim quote
    Total Downtime 29.48 2.84
  10. Lost time: 95.0 min · as reported: “Downtime machines”
    Show verbatim quote
    Downtime machines (min) 185 95 -48.65%
  11. Lost time: 185 min · as reported: “Downtime machines”
    Show verbatim quote
    Downtime machines (min) 185 95 -48.65%
  12. Share of lost time: 37.0 % · as reported: “product losses during the filling process”
    Show verbatim quote
    The analysis found two main reasons for this inefficiency: unproductive time during the packaging process, which made up 63% of the problem, and product losses during the filling process, which made up the other 37%.
  13. Share of lost time: 63.0 % · as reported: “unproductive time during the packaging process”
    Show verbatim quote
    The analysis found two main reasons for this inefficiency: unproductive time during the packaging process, which made up 63% of the problem, and product losses during the filling process, which made up the other 37%.
  14. Lost time: 160 min · as reported: “Planned losses”
    Show verbatim quote
    Planned losses (min) 0 160 0 0 0 160 7
  15. Lost time: 494 min · as reported: “Operational losses”
    Show verbatim quote
    Operational losses (min) 278 494 106 53 157 1088 48
  16. Lost time: 364 min · as reported: “Equipment losses”
    Show verbatim quote
    Equipment losses (min) 420 364 24 55 152 1015 44.8