Unspecified process defects
Die wissenschaftlichen Inhalte dieser Seite werden auf Englisch und Spanisch veröffentlicht; hier werden sie auf Englisch angezeigt.
Kurz gefasst
Sie tritt bei etwa 2 von 100 untersuchten Linien auf.
Wenn sie auftritt, entfällt auf sie im Mittel etwa 47 % der Verlustzeit der Linie. Berichtet von 6 der 127 Studien, die sie beobachten konnten (gute Evidenz).
Was passiert
Units produced during otherwise stable running fail to meet specification at first pass because of some combination of equipment drift, material variability or process parameter deviation that the primary report does not attribute to a specific machine or mechanism. The defective output is identified only in aggregate as scrap, rework or downgrade without a named root cause.
Was man dagegen tut
Improve defect tagging at the point of rejection so each loss event is linked to a specific machine, station and probable cause code, then use Pareto analysis of the resulting data to prioritize targeted root-cause investigations. In the meantime, tighten incoming material and in-process checks and reinforce operator training to reduce the undifferentiated defect rate.
Praktische Hinweise auf Basis ingenieurtechnischen Wissens; keine statistische Schätzung.
1Wahrscheinlichkeit und Evidenz
- Auftretenswahrscheinlichkeit
- 1,7 % [0,6–3,7 %]
- Erwarteter Anteil an der Verlustzeit
- 0,8 % [0,3–1,7 %]
- Anteil an der Verlustzeit bei Auftreten
- 47 % [37–57 %]
- Studien / Einheiten
- 127 / 161
- Evidenzgrad
- B
Grad B: 5 bis 9 Studien oder eine Intervallbreite zwischen 0,20 und 0,35.
2Wahrscheinlichkeit nach Segment
- Milchprodukte1,8 % [0,3–5,5 %]13 Studien
- Erfrischungsgetränke, abgefülltes Wasser und Säfte1,9 % [0,4–5,0 %]26 Studien
- Bier, Wein und Spirituosen1,8 % [0,3–5,3 %]11 Studien
- Backwaren und Teigwaren3,5 % [0,8–9,1 %]24 Studien
- Fleisch, Geflügel und Fisch2,6 % [0,5–7,5 %]9 Studien
- Obst- und Gemüseverarbeitung1,8 % [0,3–5,5 %]7 Studien
- Getreide- und Ölsaatenmüllerei1,9 % [0,3–6,0 %]6 Studien
- Zucker und Süßwaren2,5 % [0,5–7,5 %]9 Studien
- Snacks, Kaffee, Tee und sonstige Lebensmittel1,8 % [0,3–5,6 %]5 Studien
- Futtermittel und Heimtiernahrung1,8 % [0,3–5,5 %]7 Studien
- Lebensmittelherstellung (nicht spezifiziert oder gemischt)1,8 % [0,3–5,5 %]10 Studien
3Mechanismus, SCADA-Signatur und Gegenmaßnahme
Mechanismus
Ingenieurpraktische HinweiseUnits produced during otherwise stable running fail to meet specification at first pass because of some combination of equipment drift, material variability or process parameter deviation that the primary report does not attribute to a specific machine or mechanism. The defective output is identified only in aggregate as scrap, rework or downgrade without a named root cause.
So zeigt sie sich in SCADA-Daten
Ingenieurpraktische HinweiseMES/SCADA records show an aggregate defect, scrap or rework quantity or rate tied to a production order or shift, without a corresponding machine fault code, stop event or named parameter excursion. Quality or vision-inspection counters increment while machine states remain in normal run, so the loss is visible only in yield or reject tallies.
Gegenmaßnahme
Ingenieurpraktische HinweiseImprove defect tagging at the point of rejection so each loss event is linked to a specific machine, station and probable cause code, then use Pareto analysis of the resulting data to prioritize targeted root-cause investigations. In the meantime, tighten incoming material and in-process checks and reinforce operator training to reduce the undifferentiated defect rate.
4Quellen
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT XYZ Menggunakan Metode Overall Equipment Effectiveness (2019)Quelle öffnenAnteil an der geplanten Zeit: 0,134 % · laut Bericht: “Defect Losses”
Wörtliches Zitat anzeigen
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Anzahl der Ereignisse: 19,0 cases · laut Bericht: “nonconforming product”
Wörtliches Zitat anzeigen
This is reflected in the production of nonconforming product decrease from 19 cases (2010) to 3 (2013).
- Anzahl der Ereignisse: 3,00 cases · laut Bericht: “nonconforming product”
Wörtliches Zitat anzeigen
This is reflected in the production of nonconforming product decrease from 19 cases (2010) to 3 (2013).
- Enhancing operational efficiency in craft beer production: implementation of lean manufacturing and TPM methodologies in SMES (2025)Quelle öffnenFehlerquote: 2,97 % · laut Bericht: “Rate of defective products”
Wörtliches Zitat anzeigen
The rate of defective products was reduced from 2.97% to 1.30%, which is equivalent to a 56% decrease.
- Enhancing operational efficiency in craft beer production: implementation of lean manufacturing and TPM methodologies in SMES (2025)Quelle öffnenFehlerquote: 1,30 % · laut Bericht: “Rate of defective products”
Wörtliches Zitat anzeigen
The rate of defective products was reduced from 2.97% to 1.30%, which is equivalent to a 56% decrease.
- Anteil an der Verlustzeit: 19,9 % · laut Bericht: “defects”
Wörtliches Zitat anzeigen
Analysis showed the distribution of the losses with set-up and failures being the predominant with 66.4% of total lost time, followed by defects participating with 19.9% and reduced speed and minor stoppage contributing with 13.7%.
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT. Suryajaya Abadiperkasa Menggunakan Metode Overall Equipment Effectiveness (2020)Quelle öffnenAnteil an der Verlustzeit: 0,134 % · laut Bericht: “Defect Losses”
Wörtliches Zitat anzeigen
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Increased equipment performance in agro-industrial companies through a maintenance model based on the TPM approach (2022)Quelle öffnenFehlerquote: 11,8 % · laut Bericht: “productos no conformes (PNC)”
Wörtliches Zitat anzeigen
se cuenta con una línea de producción donde se obtuvo 98746 latas como productos no conformes teniendo en un índice de 11.75% de la producción planeada comparado con el margen establecido mundial
- Peningkatan Overall Equipment Effectiveness (OEE) dengan Pendekatan Total Productive Maintenance (TPM) di Line X PT Kraft Ultrajaya Indonesia (2023)Quelle öffnenAnteil an der Verlustzeit: 4,00 % · laut Bericht: “Defect Amount”
Wörtliches Zitat anzeigen
the loss factors that affect the OEE line X value are Idling and Minor Stoppage with a percentage of 8%, Setup and Adjustment with a percentage of 5%, Defect Amount with a percentage of 4%.
- Production Model Based on Lean Manufacturing, MRP, MPS and TPM to Reduce Losses in a MSE in the Bakery Sector (2023)Quelle öffnenFehlerquote: 10,0 % · laut Bericht: “Defective products rate”
Wörtliches Zitat anzeigen
Defective product index: This indicator managed to drop from 10% to 5%, with this the company achieved better profitability and had fewer economic losses.
- Production Model Based on Lean Manufacturing, MRP, MPS and TPM to Reduce Losses in a MSE in the Bakery Sector (2023)Quelle öffnenFehlerquote: 5,00 % · laut Bericht: “Defective products rate”
Wörtliches Zitat anzeigen
Defective product index: This indicator managed to drop from 10% to 5%, with this the company achieved better profitability and had fewer economic losses.
- Anteil an der geplanten Zeit: 2,20 % · laut Bericht: “Defect in process”
Wörtliches Zitat anzeigen
𝐷𝑒𝑓𝑒𝑐𝑡 𝑖𝑛 𝑝𝑟𝑜𝑐𝑒𝑠𝑠= 2,202 %
- Enhancing Operational Efficiency in Craft Beer Production: Implementation of Lean Manufacturing and TPM Methodologies in SMEs (2024)Quelle öffnenFehlerquote: 2,97 % · laut Bericht: “rate of defective products”
Wörtliches Zitat anzeigen
The rate of defective products was reduced from 2.97% to 1.30%, which is equivalent to a 56% decrease.
- Enhancing Operational Efficiency in Craft Beer Production: Implementation of Lean Manufacturing and TPM Methodologies in SMEs (2024)Quelle öffnenFehlerquote: 1,30 % · laut Bericht: “rate of defective products”
Wörtliches Zitat anzeigen
The rate of defective products was reduced from 2.97% to 1.30%, which is equivalent to a 56% decrease.
- The implementation of an integrated Lean Management-HACCP model: application in the food industry in Casablanca,Morocco (2025)Quelle öffnenFehlerquote: 5,00 % · laut Bericht: “non-compliant products”
Wörtliches Zitat anzeigen
Only 5% of non- compliant products per month
- The implementation of an integrated Lean Management-HACCP model: application in the food industry in Casablanca,Morocco (2025)Quelle öffnenVerlustzeit: 5,00 min · laut Bericht: “non-conformity”
Wörtliches Zitat anzeigen
the non- conformity time to 5 minutes
- The implementation of an integrated Lean Management-HACCP model: application in the food industry in Casablanca,Morocco (2025)Quelle öffnenVerlustzeit: 10,0 min · laut Bericht: “Non-quality/ Non-conformity”
Wörtliches Zitat anzeigen
Non-quality/ Non-conformity 10 min
- The implementation of an integrated Lean Management-HACCP model: application in the food industry in Casablanca,Morocco (2025)Quelle öffnenFehlerquote: 20,0 % · laut Bericht: “products with defects”
Wörtliches Zitat anzeigen
20% ofproductswithdefects /month
- A Lean Manufacturing Case Study: Enhancing Efficiency and Reducing Waste in Latin American Food Production (2024)Quelle öffnenAnteil an der Verlustzeit: 25,0 % · laut Bericht: “high rate of defective products”
Wörtliches Zitat anzeigen
At the first level, three main reasons were identified: a high rate of decline (55%), a high rate of defective products (25%), and elevated unproductive times (20%).
- Integrating Lean Manufacturing and TPM for Production Efficiency Improvement: A Peruvian Case Study in the Bottled Water Industry (2024)Quelle öffnenFehlerquote: 3,13 % · laut Bericht: “product defects”
Wörtliches Zitat anzeigen
Discards rate | % | 3.13% | 2% | 0.96% | -69.33%
- Integrating Lean Manufacturing and TPM for Production Efficiency Improvement: A Peruvian Case Study in the Bottled Water Industry (2024)Quelle öffnenFehlerquote: 0,960 % · laut Bericht: “product defects”
Wörtliches Zitat anzeigen
Discards rate | % | 3.13% | 2% | 0.96% | -69.33%
- Reliability-Centered Maintenance Model to Improve OEE in a Mass-Consumption Food Company: A Case Study from Peru (2025)Quelle öffnenAnteil an der Verlustzeit: 4,30 % · laut Bericht: “defective products”
Wörtliches Zitat anzeigen
The analysis revealed three main reasons contributing to this issue: production line stoppages accounted for 49.2% of the problem, followed by low operational performance with a contribution of 46.5%, and a smaller share of 4.3% attributed to defective products.
- Productivity Improvement Through the Application of Lean Six Sigma Tools in a Non-Alcoholic Beverage Company (2025)Quelle öffnenFehlerquote: 9,62 % · laut Bericht: “non-conformance”
Wörtliches Zitat anzeigen
Defect rate (%) 9.62% 5.80 – 6.00 % – 40 %
- Verlustzeit: 70,0 min · laut Bericht: “Produto não conforme”
Wörtliches Zitat anzeigen
Produto não conforme 12 845 1 087,07 € 70
- Anzahl der Ereignisse: 12,0 events · laut Bericht: “Produto não conforme”
Wörtliches Zitat anzeigen
Produto não conforme 12 845 1 087,07 € 70

