Rework of off-specification product
In short
It appears in about 2 of every 100 lines studied.
When it appears, it takes on average about 46 % of the line's lost time. Reported by 5 of the 127 studies that could observe it (good evidence).
What happens
Product or packages produced during stable running fail to meet weight, fill, seal, appearance or other quality specifications at first pass and must be diverted for reprocessing, re-filling, re-labeling or re-packing instead of being accepted as good output. The underlying root causes can be process drift, material variability or minor equipment misadjustment, but the loss itself is the material, time and capacity consumed in recovering the units rather than scrapping them.
What is done about it
Tighten process control (fill weight, seal temperature/pressure, closure torque) through SPC and automatic feedback loops to reduce the generation of off-spec units at the source, and standardize rework procedures with clear acceptance criteria to minimize the handling time per diverted unit. Root-cause the recurring defect types feeding rework and address them through equipment calibration, material qualification or operator training rather than relying on downstream recovery.
Practical guidance written from engineering knowledge; it is not a statistical estimate.
1Probability and evidence
- Probability of presence
- 1.5% [0.5–3.4%]
- Expected share of lost time
- 0.7% [0.2–1.6%]
- Share of lost time when present
- 46% [35–57%]
- Studies / units
- 127 / 161
- Evidence grade
- B
Grade B: 5 to 9 studies, or an interval width between 0.20 and 0.35.
2Probability by segment
- Dairy products1.6% [0.3–4.9%]13 studies
- Soft drinks, bottled water and juices1.8% [0.4–5.0%]26 studies
- Brewing, wine and spirits4.3% [0.8–12.7%]11 studies
- Bakery and pasta1.4% [0.2–3.8%]24 studies
- Meat, poultry and seafood1.6% [0.2–5.2%]9 studies
- Fruit and vegetable processing1.7% [0.2–5.4%]7 studies
- Grain and oilseed milling1.7% [0.3–5.3%]6 studies
- Sugar and confectionery2.2% [0.4–6.8%]9 studies
- Snacks, coffee, tea and other foods1.7% [0.2–5.5%]5 studies
- Animal feed and pet food1.6% [0.3–5.0%]7 studies
- Food manufacturing (unspecified or mixed)1.6% [0.2–5.2%]10 studies
3Mechanism, SCADA signature and countermeasure
Mechanism
Engineering guidanceProduct or packages produced during stable running fail to meet weight, fill, seal, appearance or other quality specifications at first pass and must be diverted for reprocessing, re-filling, re-labeling or re-packing instead of being accepted as good output. The underlying root causes can be process drift, material variability or minor equipment misadjustment, but the loss itself is the material, time and capacity consumed in recovering the units rather than scrapping them.
How it looks in SCADA data
Engineering guidanceMES/quality modules show elevated counts of units flagged as rework or rejected-but-recoverable, often tied to a diversion or reject-lane actuator cycling, with a parallel rework or reprocessing line showing increased throughput and run time. Checkweigher, vision or seal-tester reject counters rise while overall line OEE availability stays largely unaffected, concentrating the loss in the quality/yield metric rather than in downtime.
Countermeasure
Engineering guidanceTighten process control (fill weight, seal temperature/pressure, closure torque) through SPC and automatic feedback loops to reduce the generation of off-spec units at the source, and standardize rework procedures with clear acceptance criteria to minimize the handling time per diverted unit. Root-cause the recurring defect types feeding rework and address them through equipment calibration, material qualification or operator training rather than relying on downstream recovery.
4Sources
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT XYZ Menggunakan Metode Overall Equipment Effectiveness (2019)Open sourceShare of planned time: 0 % · as reported: “Rework Losses”
Show verbatim quote
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Open sourceNumber of events: 4.00 Boxes x 12 · as reported: “Rework”
Show verbatim quote
Rework Average 7 4
- Optimizing beverage manufacturing: integrating lean manufacturing and machine learning to enhance efficiency and reduce waste (2025)Open sourceNumber of events: 7.00 Boxes x 12 · as reported: “Rework”
Show verbatim quote
Rework Average 7 4
- Enhancing operational efficiency in craft beer production: implementation of lean manufacturing and TPM methodologies in SMES (2025)Open sourceShare of lost time: 14.0 % · as reported: “reprocessing”
Show verbatim quote
Among the main causes identified, errors in the conduct of operations accounted for 39.20%, reprocessing constituted 13.95%, and process shutdowns due to machine failures covered 46.85%.
- Analisis Efektivitas Mesin pada Divisi Pengalengan Jamur Di PT. Suryajaya Abadiperkasa Menggunakan Metode Overall Equipment Effectiveness (2020)Open sourceShare of lost time: 0 % · as reported: “Rework Losses”
Show verbatim quote
Rata-Rata 0,099271 9,29814 30,74813 0,00000 0,00000 0,13414
- Enhancing Operational Efficiency in Craft Beer Production: Implementation of Lean Manufacturing and TPM Methodologies in SMEs (2024)Open sourceShare of lost time: 14.0 % · as reported: “reprocessing”
Show verbatim quote
errors in the conduct of operations accounted for 39.20%, reprocessing constituted 13.95%, and process shutdowns due to machine failures covered 46.85%.
- Optimizing Beverage Manufacturing: Integrating Lean Manufacturing and Machine Learning to Enhance Efficiency and Reduce Waste (2024)Open sourceDefect rate: 12.0 % · as reported: “reprocessing”
Show verbatim quote
The main issues concerning the product process include 25% of incorrectly labeled bottles, 18% of improperly sealed bottles, and 12% of reprocessing in the current alcoholic beverage production process.
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Open sourceShare of lost time: 22.0 % · as reported: “Rework Losses”
Show verbatim quote
Rework Losses 8.890 29.095 22% 72%
- Aggregate Analysis of Packaging Machine Effectiveness Using the OEE Method at PT. XYZ (2025)Open sourceLost time: 8,890 Minutes · as reported: “Rework Losses”
Show verbatim quote
Rework Losses 8.890 29.095 22% 72%
- Enhancing Operational Effectiveness in a Beverage Bottling SME through SMED, 5S, and TPM Maintenance Practices (2025)Open sourceShare of lost time: 19.0 % · as reported: “the necessity for product reprocessing”
Show verbatim quote
Detailed decomposition of the shortfall reveals that parasitic machine velocity losses exert a 47% share on ineffective output, protracted repair durations 34%, and the necessity for product reprocessing 19%.
- Machine Learning, MRP, and Lean Tools as an Internal Innovation Strategy to Improve Efficiency in a Bottling Company (2025)Open sourceDefect rate: 19.0 % · as reported: “rework”
Show verbatim quote
In the initial process diagnosis, an inefficiency level of 19% was identified, reflecting high variability, rework, and bottlenecks.
- Machine Learning, MRP, and Lean Tools as an Internal Innovation Strategy to Improve Efficiency in a Bottling Company (2025)Open sourceDefect rate: 13.0 % · as reported: “rework”
Show verbatim quote
With the validation of the pilot test, this value was reduced to 13%, representing a relative improvement of 32% compared to the initial condition.
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Open sourceDefect rate: 25.0 % · as reported: “reprocessing”
Show verbatim quote
Reprocessing: 25% → 5%
- Improving Production Efficiency in a Chocolate SME through Continuous Flow, SMED and Poka-Yoke (2026)Open sourceDefect rate: 5.00 % · as reported: “reprocessing”
Show verbatim quote
Reprocessing: 25% → 5%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Open sourceLost time: 0 menit · as reported: “Rework Loss”
Show verbatim quote
Rework Loss 0 0% 100%
- Penerapan Konsep Total Productive Maintenance (TPM) dalam Peningkatan Overall Equipment Effectiveness (OEE) pada Mesin Pengisian Botol di PT Trita Musi Prasada (2026)Open sourceLost time: 0 menit · as reported: “Rework Loss”
Show verbatim quote
Rework Loss 0 0% 100%

